Hardware
Print the pod
The print files of the pod and the brackets, the earlier design, for FDM and for resin.
The pod is the earlier design: the case on a bracket on the printer. The Slate v4 replaces it.
These are the files of the pod, the earlier design on a printer bracket. The Slate v4, a case on the desk, replaces it: see the Slate v4 print files. The webcam mounts in this folder stay on the printer frame.
Each file is in its print orientation. Load a file and print it as it is.
FDM (fdm/)
- Turn supports off. No part needs supports. Supports fill the screw holes, the insert holes and the groove of the TAZ bracket, and stay in the part.
- Set Z Seam Alignment to Sharpest Corner and Seam Corner Preference to Hide Seam. This keeps the seam off the round corners.
- Print the parts in the table. All parts fit on the TAZ Workhorse and the Mini 2 (0.5 mm nozzle).
- Print the cable clips in PETG. PLA can crack where their arms bend.
To turn supports off in Cura, clear Generate Support (Support section) for all parts. For one part: select it, click Per Model Settings, click Select settings, select Generate Support, click Close, and clear the box.
| File | On the bed | |
|---|---|---|
pod-frame_fdm.stl | 1 | Its back ring |
pod-body_fdm.stl | 1 | Its back |
pod-mount_fdm.stl | 1 | The face that goes on the body |
pod-wedge_fdm.stl | 1 for each bracket | Its level bottom (it stands up) |
pod-bracket-taz_fdm.stl | 1, for the TAZ | The top end of the plate (it stands up, 89 mm high). Use a 5 mm brim. |
pod-bracket-mini2_fdm.stl | 1, for the Mini 2 | The side of the plate that goes on the frame |
pod-shim-0.5mm_fdm.stl, pod-shim-1.0mm_fdm.stl, pod-shim-2.0mm_fdm.stl | 1 each, for the TAZ | Flat |
camera-arm-taz_fdm.stl | 1, for the webcam on the TAZ (option) | Its back face |
camera-clamp-taz_fdm.stl | 1, for the webcam on the TAZ (option) | Its bottom. Use a brim: it is 126 mm tall. |
camera-arm-mini2_fdm.stl | 1, for the webcam on the Mini 2 (option) | Its back face |
camera-clamp-mini2_fdm.stl | 1, for the webcam on the Mini 2 (option) | Its bottom |
camera-link_fdm.stl | 1, for the webcam on either printer (option) | The top face of its plate |
cable-clip-single_fdm.stl | 5, for the TAZ | The base |
cable-clip-double_fdm.stl | 2, for the Mini 2 | The base |
The fit
The dovetail of the pod and the key of the wedge taper. Push each part down by hand until it is tight. To remove it, pull it up.
On the TAZ, the nub of the bracket is 2.5 mm off the cover. Fill the gap with shims:
- Put the bracket on the two rail clips. Loosen the cover screw.
- Put shims between the nub and the cover until they fill the gap with no force. The shims are 0.5, 1.0 and 2.0 mm thick.
- Tighten the cover screw, an M3 x 10 with a washer.
Resin (resin/)
These files are for the Peopoly Phenom and standard resin. Each part stands on supports, 6 mm over the plate. The body, the frame, the mount, the wedge and the TAZ bracket fit on one plate.
The resin parts use captive M3 hex nuts in place of the heat-set inserts:
- Frame: put the 4 nuts in the pockets before the display goes on.
- Mount: slide the 2 nuts into the pockets before the mount goes on the body.
Print the mount and the wedge first, and try the fit.
| File | Supports on | Keep clean |
|---|---|---|
pod-body_resin.stl | The open front: the rim and the inside | The back, the side walls, the posts and the ports |
pod-frame_resin.stl | The bottom end, and the inside of the top end | The back ring, the side walls, and the front rim |
pod-mount_resin.stl | The lower end of the plate and of the dovetail | The dovetail and the face on the body |
pod-wedge_resin.stl | The level bottom | The slot and the key |
pod-bracket-taz_resin.stl | The top end and the back of the plate | The front of the plate and its edges, the groove, and the clip slots |
Slicer settings:
- Layer height 0.05 mm. Print the parts solid.
- Supports: medium density, about 3 to 4 mm apart. Tip contact 0.3 to 0.4 mm, and 0.25 to 0.3 mm on the rim of the body. Use heavy supports and a raft.
- Remove each support tip on a "Keep clean" face.
- Put no supports in the groove of the bracket, the clip slots, the slot of the wedge, or the nut pockets.
- After the cure, sand the rim of the body flat on sandpaper on glass.
Resin, flat on the plate (resin-flat/)
The same resin parts, flat on the plate with no supports. The back of the body and the frame come out flat, with no support marks.
| File | On the plate |
|---|---|
pod-body_resin-flat.stl | Its back |
pod-frame_resin-flat.stl | Its back ring |
pod-mount_resin-flat.stl | The face that goes on the body |
pod-wedge_resin-flat.stl | Its level bottom (it stands up) |
pod-bracket-taz_resin-flat.stl | The top end of the plate (it stands up, 89 mm high) |
pod-bracket-mini2_resin-flat.stl | The side of the plate that goes on the frame |
pod-shim-0.5mm_resin-flat.stl, pod-shim-1.0mm_resin-flat.stl, pod-shim-2.0mm_resin-flat.stl | Flat |
Slicer settings:
- No supports and no raft.
- Base layers: about 4 to 6, with the lowest base exposure that holds.
- Lift: slow for the base layers and the first 2 mm.
- Print the body and the frame on one plate, and the other parts on a second plate. Print the TAZ bracket on its own plate.
- Remove the parts with a thin scraper. Keep the scraper off the chamfered edge.
Print the cable clips in PETG on an FDM printer. Standard resin cracks where the arms bend. The resin clip files are for tough resin only.
Hardware for the pod
| Part | Count | Where |
|---|---|---|
| M2.5 x 4 screw | 8 | In the box of the display: 4 hold the frame to the display, 4 hold the Pi |
| M3 heat-set insert, 4 mm long | 6 | FDM parts only: 4 in the bosses of the frame, 2 in the mount. Press each insert flush with the face. |
| M3 x 6 cap screw | 6 | 4 down the posts of the body into the frame, 2 from inside the body into the mount |
| M3 hex nut (5.5 mm across the flats, 2.4 mm thick) | 6 | Resin parts only, in place of the 6 heat-set inserts |
Webcam (option)
camera.py has a mount for an Arducam B0561 camera on each printer. Each mount is a clamp on the frame, an arm with the hinge, and a link on the hinge. The camera comes in a U bracket. The base of the U hangs under the plate of the link, and the pivot of the U sets the tilt. camera_models.py has the models of the camera and the link.
The camera has its own 1 m cable, USB-A to JST. With the Slate v4, the camera stays on the printer frame. Its cable runs from the printer frame to the Slate on the desk. Measure the route before you buy a cable: camera_models.py prints the length of the route to the pod.
| Part | Count | Where |
|---|---|---|
| M3 x 16 cap screw | 1 | The hinge: through the lugs of the arm and the tongue of the link |
| 1/4"-20 x 1/4" cap screw | 1 | Down through the plate of the link into the thread of the U bracket |
| M3 heat-set insert, 4 mm long | 2 | In the tab of the clamp |
| M3 x 18 cap screw | 2 | Through the post of the arm into the inserts |
| M3 x 8 cap screw and M3 roll-in T-nut (2020, 6 mm slot) | 2 each | TAZ: the saddle on the front right upright |
| M3 frame screw, 5 mm longer | 2 | Mini 2: in place of the two frame screws of the front right corner |
cable-clip-single | 4 (TAZ) or 3 (Mini 2) | Along the frame to the deck, on 12 x 12 mm foam tape |
- Press the two inserts into the tab of the clamp.
- Put the tongue of the link between the two lugs of the arm, with the plate to the front. Put the M3 x 16 screw through the thin lug and the tongue, into the thick lug. Set the plate level, and tighten the screw until the link stays.
- Put the base of the U bracket under the plate of the link. Put the 1/4"-20 x 1/4" screw down through the plate into the base, and tighten it.
- Put the post of the arm in the channel of the tab. Put in the two M3 x 18 screws.
- TAZ Workhorse: roll the two T-nuts into the front slot and the right slot of the front right upright, under the corner plate. Put the saddle keys into the slots, and tighten the two M3 x 8 screws.
- Mini 2: remove the two frame screws on the right face of the front right corner. Put the lip of the plate on the top of the frame, and put in the two longer screws.
- Turn the camera on the pivot of the U: about 52 degrees down on the TAZ, 46 degrees on the Mini
- Tighten the two pivot screws.
- Plug the cable into the back of the camera. Run the cable in the clips to the deck. Coil the rest of the cable and tie it.
To remove the camera, unplug it and remove the two screws of the arm.
Download
FDM
cable-clip-double_fdm.stlcable-clip-single_fdm.stlcamera-arm-mini2_fdm.stlcamera-arm-taz_fdm.stlcamera-clamp-fit-taz_fdm.stlcamera-clamp-mini2_fdm.stlcamera-clamp-taz_fdm.stlcamera-link_fdm.stlfit_holes_fdm.stlpod-body_fdm.stlpod-bracket-mini2_fdm.stlpod-bracket-taz_fdm.stlpod-frame_fdm.stlpod-mount_fdm.stlpod-shim-0.5mm_fdm.stlpod-shim-1.0mm_fdm.stlpod-shim-2.0mm_fdm.stlpod-wedge_fdm.stlclip.stl (TAZ Workhorse)
Resin
cable-clip-double_resin.stlcable-clip-single_resin.stlcamera-arm-mini2_resin.stlcamera-arm-taz_resin.stlcamera-clamp-fit-taz_resin.stlcamera-clamp-mini2_resin.stlcamera-clamp-taz_resin.stlcamera-link_resin.stlpod-body_resin.stlpod-bracket-mini2_resin.stlpod-bracket-taz_resin.stlpod-frame_resin.stlpod-mount_resin.stlpod-shim-0.5mm_resin.stlpod-shim-1.0mm_resin.stlpod-shim-2.0mm_resin.stlpod-wedge_resin.stl
Resin, flat on the plate
cable-clip-double_resin-flat.stlcable-clip-single_resin-flat.stlcamera-arm-mini2_resin-flat.stlcamera-arm-taz_resin-flat.stlcamera-clamp-fit-taz_resin-flat.stlcamera-clamp-mini2_resin-flat.stlcamera-clamp-taz_resin-flat.stlcamera-link_resin-flat.stlpod-body_resin-flat.stlpod-bracket-mini2_resin-flat.stlpod-bracket-taz_resin-flat.stlpod-frame_resin-flat.stlpod-mount_resin-flat.stlpod-shim-0.5mm_resin-flat.stlpod-shim-1.0mm_resin-flat.stlpod-shim-2.0mm_resin-flat.stlpod-wedge_resin-flat.stl